The Jalopy Journal
All lines and wires are new ,elevation wise maybe 2 feet ?
DP , in one case the pump blew when the 5 amp fuse blew First 2 were on 15 amp was fuses
I am having major headaches over a 12 volt fuel pump install ….I have burnt up 4 so far !! I have done many of these with no problem Just TWO...
I’ve searched every posed I could find on here I’m sure an “”F “” needs to be on the end for the vett , but could not figure out /find what the...
Based on these pictures could someone please tell me what I have ? I understand it is a 56 motor but could not find the”H” reference, I guess the...
Would the 265 be the Spitfire ? I have a one in my garage that I was going to put in my 53 T&C when the Spitfire turned out be roached Sent...
I am selling out everything do to health, I anticipate a large auction of entire shop , please note these items are in Northern Michigan , I...
I realize this is an old thread but this may help after you get the new bushings in .... adjusting the shifter [MEDIA] Oldog
I read a couple posts that said this would help on the shaft along with heating up the balancer but I am afraid that heat may damage or weaken...
Squirrel, It was tight make me nervous once it broke loose Slade right out of there with my fingers .. Working on the front seal now figuring how...
Squirrel, Do you have a part number for that balancer ? I went to doorman website chatted with a guy the books only go back to 65 and I have a 64...
The manual says tap with brass pin punch until protruding from opposite side and “ roll “ out with pliers .. I taped it with a steel punch and it...
Here is what I found and also the supplement has it where you do not have to lift or remove crank ..
Squirrel, I have both the 1961 manual and the 1964 supplement... I was referring to the first when I should have looked at the supplement.. they...
Squirrel, I guess your referring to the “ upper half “ as of I is being changed in the car ? Here is the one I bought as recommended in a...
Getting ready to tackle changing of the rear main seal on removed engine from my 64 Bel Air . From google I have heard everything from using a...
If anyone is interested for future reference Thanks !!!
Hello , this is the back side of the part that goes from between the exhaust/intake manifolds up to the Rochester B carb I have . I am assuming...
You rock ! Carb fixed ....check TDC fixed ......check Now ...Starter When the (project) car sits for a day starter will roll over with the key a...
Couldn’t figure delete 1940
You Rock ! Carb fixed......check TDC fixed .....check Now Starter problem .... When the (project) car sits for a day starter will roll over with...
"Budget36......Or, move all the wires over one on the cap... That’s what I was looking for ... as always I over look the obvious.thanks bud
Bandit , no I come here to to find excellent advise and more than usually do .. what I was asking was some help figuring out a brain fart on my...
I got it in there’s the correct way ... I guess I was asking how to do it the wrong way . Thanks all ! Dan
Thanks all, 2 part answer .. how I find TDC on the COMPRESSION stroke is actually quite easy. If you look at the picture there is a spark plug...
Re ; 1964 Chevy 230 6 cylinder With #1 at just before TDC. ( no mark ) Rotor button is pointed at #1 ( one o’clock )and vacuum advance is pointed...
To all , like all of us if I have something that is not working correctly I am too anal sometimes about fixing it , often throwing good $ after...
302 ... did you see this in a quotefrom a Mike’s Carb Blog ? I will get with them tomorrow. “””Also of note is that this is a leather pump and...
Jon , what is this ? What I took out is on right.. Thank you Dan
Separate names with a comma.